2021 Audi Q5

2021 Audi Q5 SUV AWD

Overall

★★★★★

Front Crash

★★★★★

Side Crash

★★★★★

Rollover

★★★★☆

SEAT BELTS:REAR/OTHER:RETRACTOR

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2021 Volkswagen ID4, Audi A4 Allroad, A4 Sedan, A5 Cabriolet, A5 Coupe, A5 Sportback, A6 Allroad, A6 Sedan, A7, A8, E-Tron Quattro, E-Tron Sportback Quattro, Q3, Q5, Q5 Sportback, Q7, Q8, RS5 Sportback, RS5 Coupe, RS6 Avant, RS7, RSQ8, S4 Sedan, S5 Cabriolet, S5 Coupe, S5 Sportback, S6 Sedan, S7, S8, SQ5, SQ5 Sportback, SQ7, SQ8, and 2021-2022 S3 Sedan vehicles. The rear seat belt automatic locking retractors may deactivate early, which can prevent the child restraint system from securing properly. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."

Campaign: 21V606000

TIRES

Volkswagen Group of America, Inc. (Audi) is recalling certain 2019-2021 Audi A5 Sportback, RS5 Coupe, RS5 Sportback, S5 Sportback, 2020-2021 A4 Allroad, A4 Sedan, A5 Cabriolet, A5 Coupe, A6 Allroad, A6 Sedan, A7, A8, Q5, S4 Sedan, S5 Coupe, S5 Cabriolet, S6 Sedan, S7, S8, SQ5, 2021 Q5 Sportback, Q7, Q8, RS6 Avant, RS7, RSQ8, SQ5 Sportback, SQ7, and SQ8 vehicles. The rear axle alignment may not have been inspected after the repairs for Recall 21V-295 (42L1) were performed.

Campaign: 22V034000

ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM

Volkswagen Group of America, Inc. (Audi) is recalling certain 2021-2022 Q5 Sportback, SQ5 Sportback, 2018-2022 Q5, and SQ5 vehicles. A liquid spill in the rear seat, or water ingress from an insufficient body seam underneath the vehicle may allow liquid to penetrate the gateway control module, causing it to shutdown.

Campaign: 21V947000

SUSPENSION:REAR:AXLE:NON-POWERED AXLE ASSEMBLY

Volkswagen Group of America, Inc. (Audi) is recalling certain 2021 Q7, Q8, Q5 Sportback, SQ5 Sportback, RS6 Avant, RS7, RS Q8, 2020-2021 Audi S6 sedan, Q5, A8, S8, A7, A6 Allroad, A5 Cabriolet, A4 sedan, A4 Allroad, SQ5, S7, A6 sedan, S5 coupe, S4 sedan, S5 Cabriolet, A5 coupe, 2019-2021 RS5 coupe, A5 Sportback, S5 Sportback, RS5 Sportback vehicles. The lock nut on the trailing arm of the rear axle may break due to stress corrosion.

Campaign: 21V295000

BACK OVER PREVENTION:DISPLAY FUNCTION

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2021 Audi A8, RS7, RS6 Avant, RS5 Sportback, RS5 Coupe, Q8, Q7, Q5 Sportback, S4 Sedan, Q5, A7, A6, A6 Allroad, A5 Sportback, A5 Coupe, A5 Cabrioleet, A4 Sedan, A4 Allroad, E-Tron Sportback Quattro, SQ7, S5 Cabriolet, E-Tron Quattro, SQ8, SQ5 Sportback, SQ5, S8, S7, S6 Sedan, S5 Sportback, S5 Coupe, 2022 E-Tron GT, and 2021-2022 RSQ8 vehicles. Due to a software issue, a blank or black screen may be displayed instead of the rearview camera image when the vehicle is placed in reverse gear. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."

Campaign: 22V742000

ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2021-2023 Audi Q5 Sportback, Q5, 2022-2023 Volkswagen Atlas FL, and Atlas Cross Sport vehicles. The engine connecting rod bearings may become damaged, which can result in engine failure.

Campaign: 22V753000

ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:CABLE/CORD:ONBOARD

Volkswagen Group of America, Inc. (Audi) is recalling certain 2022-2024 RS e-tron GT, e-tron GT, Q4 e-tron Sportback, Q4 e-tron, 2020-2021 Audi A8, 2019-2024 e-tron Quattro, 2020-2024 e-tron Sportback Quattro, Q5, and 2021-2022 A7 vehicles. When using the industrial 220V/240V plug at the 100% charge setting, some home power outlets may be incapable of handling the electrical current required to utilize the compact charging system, causing the outlet or charging cable to overheat.

Campaign: 23V842000

ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2021-2024 Audi Q5, and 2022 A7 E Hybrid Electric PHEV vehicles. The high-voltage battery may overheat.

Campaign: 25V080000

ENGINE

I was driving at highway speeds when a "Transmission Malfunction" warning appeared, and the vehicle lost the ability to accelerate. Once I was able to pull over and put the vehicle in Park, it completely lost the ability to engage Drive or Reverse, leaving me stranded. Important to note pulling over was difficult as I was on a highway driving ar 70mph speed and trying to locate safe space to stop avoid collusion. My car towed to the nearest dealership for repairs. Audi dealership confirmed the cause was broken internal transmission filter housing bolts. I was told this was premature occurrence as the vehicle only has 35,760 miles of driving and no prior work done on the transmission or visible notice of damage that could cause this issue.

ELECTRICAL SYSTEM,ENGINE,FUEL/PROPULSION SYSTEM

If I have a sensor that will malfunction due to water then there should be a water indicator alert. My sunroof vent was blocked and water went into my trunk where the core module is. I had just come to a red light to turn on to a major highway and my car began to smell like fuel. I rolled down the windows and realized the smell was not as strong as inside. The light turned green and as I stepped on the gas the car went into limp mode as I was in the middle of my turn. The power steering then went out in the turn and the wheel yanked to the left and put me half way into the lane next to me. Thankfully no one was there. I had to yank it back to the right to get off of the highway on to the side of the road. I do not think that the power steering should be associated with that module or at least a water indicator sensor should be added. What happens if someone is on the interstate is driving 75 mph and their power steering goes out. It's in the shop and there is no damage other than now I am scared to drive it

ENGINE AND ENGINE COOLING

The contact owns a 2021 Audi Q5. The contact stated that while driving approximately 55 MPH, the vehicle lost motive power and the vehicle decelerated before the vehicle stalled. During the failure, the check engine, oil, and coolant warning lights were illuminated. The vehicle was later towed to the local dealer to be diagnosed. The dealer determined that the engine bearings had failed, causing catastrophic damage to the engine. The contact was advised that the engine needed to be replaced. The vehicle was not yet repaired. The contact was informed that the VIN was not included in the NHTSA Campaign Number: 22V753000 (ENGINE AND ENGINE COOLING). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 43,000.

FORWARD COLLISION AVOIDANCE

I was driving down a regular road by my house, full sunshine, perfect road, nothing unusual. In fact, it was such a nice day, the sunroof was open and windows were down. My dog was in the back seat after just being picked up from grooming happily enjoying the day with his head out the window. I was on a road with the speed limit of 30. I was going 30 mph. Nothing unusual. Literally, out of nowhere, like my car was possessed, is the best way I put it, my car abruptly braked in an attempt to stop on a dime. My car screeched to a stop while simultaneously my windows rolled up, my sunroof closed and my seat belt tightened, locking me in place. My dog was thrown forward. It was terrifying! Luckily, no one was behind me or they would have certainly rear-ended me. Nothing was in the road. Absolutely nothing. It happened so quickly in a split second. I put my hazards on and finished the next 2 miles home. I called Audi for a service appointment. I took my car in, again going down back roads with my hazards on. Audi charged me $400 to run a diagnostic report and shows there is a fault code J428. This fault code I researched is for the front/right ACC radar sensor that powers Adaptative Cruise control and Pre-Sense braking system. The fault code erroneously detected an obstacle and did abrupt braking. Audi told me that they would charge me $4,000 to fix it. I contested that as a safety issue it should be fixed as there is also Audi TSB2063502 referencing problems. This is a major safety issue as if I was going 70 MPH, I could cause a massive accident where I could be killed, anyone in my car, as well as others behind me in a massive car pile up. I feel ethically, this must be a safety recall to replace this fault in all vehicles. I am also requesting payment to fix from Audi. As an attorney (#[XXX]), Audi is under notice that they have a major safety defect on their hands and should take steps to protect drivers safety. Thank you. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Carry Handle, Shell, Base

The car seat comes loose every month and has to be reinstalled

SERVICE BRAKES

I am submitting this complaint regarding a serious brake-related safety issue involving my Audi vehicle after recent brake service performed by an authorized Audi Meadowland dealership in [XXX] . In December 2025, I brought my vehicle to an authorized Audi dealership for replacement of the brake pads. The repair was completed by the dealership, and I trusted that the vehicle was safe to drive afterward. However, only approximately six months later, and after driving only around 1,000 miles since the repair, the vehicle experienced a dangerous brake-related failure involving the brake pad assembly becoming loose/detached while the vehicle was in operation. This incident occurred while my entire family was inside the vehicle, creating a serious safety hazard and placing all occupants at risk. A brake system component should not fail after such a short period of time and limited mileage following dealership service. In addition to the safety concern itself, I am also extremely dissatisfied with the dealership’s handling of the matter. The dealership did not proactively contact me regarding the repair status, and multiple attempts to contact them by phone went unanswered. I believe this issue may involve improper installation, defective parts, insufficient inspection procedures, or other serious safety-related service failures. I respectfully request that NHTSA review and investigate this matter to determine whether similar incidents may affect other vehicles serviced under similar conditions. Thank you in advance for your review on this matter. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

ELECTRICAL SYSTEM,STRUCTURE

The contact owns a 2021 Audi Q5. The contact stated that while driving at an undisclosed speed, several unknown warning lights illuminated, and the vehicle stalled. Additionally, the windows independently rolled up and down, and the engine seized. While attempting to start the vehicle, the vehicle failed to start. The contact stated that the failure had occurred three times within five days. The vehicle was towed to the dealer where it was purchased. The failure was diagnosed with a failed gateway control module. The contact was informed that the gateway control module needed to be replaced. The vehicle was being repaired. The contact was informed that the plastic protective bag that covered the gateway control module was filled with water. In addition, the dealer informed the contact that the NHTSA Campaign Number: 21V947000 (Electrical System, Structure); recall repair was performed prior to the contact purchasing the vehicle. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 37,200.

ELECTRICAL SYSTEM,UNKNOWN OR OTHER

The safety situation happened when my wife's car got stuck while driving at about 25-30 MPH in the middle of the road.Next day At the nearest Audi service center they found that water has gotten into the rear of the trunk and damaged the electronic module which caused the car to stall.The first repair was estimate at 4600 $ .After the repair the car was inoperable.The next repair was estimated at another 4 700 $.After the second repair the car was inoperable again and the service department told me that the car needed to replace the entire transmission .Which they estimated at another 20 000 $. So the total damage is around 30 000$ .I contacted Audi USA about the whole situation when I received a negative message regarding the solution . I would like to point out that up until the moment mentioned we had no problems with the car .After my personal investigation of the problem ,I found that there was a safety recall # 21V-947 for same problem .It was not issued for my car which meets all the criteria.It looks like it was hidden by the manufacturer. Audi distances itself from the whole problem and refuses to cover the costs of the damage.Thank good this happened on the city road where the speed is low .If this happened on the highway at 60 MPH it would have had tragic consequences .Where it would never have been figured out what caused the accident. From a safety perspective ,I m reporting this dangerous and unfair treatment of customers by AUDI USA regarding the hidden recall and denial of resposability that occurred and I request an investigation .

POWER TRAIN,ELECTRICAL SYSTEM,ENGINE

Control module located under rear seat became slightly wet from spilled liquid, and failed. Engine and electrical failure as a result of control module failure. Audi refuses to cover damages as warranty period is over. Vehicle design is defective.

FORWARD COLLISION AVOIDANCE,LANE DEPARTURE

Following a rear collision repair at an authorized dealer collision center, multiple ADAS safety systems were not properly calibrated despite insurance payment and shop representations that repairs were complete. WHAT FAILED: Lane Change Assist, Peripheral Camera System, Side Assist, 360-Degree Camera, Front Camera, and Adaptive Cruise Control were either not calibrated or calibrated in timeframes physically incompatible with manufacturer specifications. SAFETY RISK: Driver relies on blind spot monitoring and lane change alerts that may be non-functional or inaccurate. Without proper calibration, these systems may fail to detect adjacent vehicles, provide false alerts, or create blind spots in camera coverage, increasing collision risk during lane changes and merging. DEALER CONFIRMATION: Yes. Shop manager provided diagnostic logs as proof of calibration. Analysis shows 360-degree camera calibration executed in 18 seconds versus 40-60 minute industry standard, and zero calibration events logged for Lane Change Assist and Peripheral Camera systems explicitly claimed as completed. INSURANCE INSPECTION: Insurance company explicitly DENIED Lane Change Assist and Peripheral Camera calibrations on estimate. Shop admitted in writing these items were declined and blamed insurance for non-payment. No OEM calibration logs produced despite multiple written requests. WARNING SYMPTOMS: Systems may appear normal on diagnostic scan with no active fault codes, but this does not prove calibration was performed to OEM tolerances. Physical calibration requires target board positioning, laser alignment, and environmental verification that cannot be completed in documented timeframes. PATTERN CONCERN: This may represent a systemic issue where insurers deny ADAS calibrations, shops skip calibrations due to non-payment, vehicles are released as complete, and consumers unknowingly operate vehicles with compromised safety systems. Vehicle and documentation available for inspection.