Skip to content

FreeVIN

2018 Jeep Wrangler

Recalls, consumer complaints and crash ratings from NHTSA

Recalls14

  • Back over preventionSensing system, cameraSep 12, 2024, Campaign 24V676000

    Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."

    Risk

    A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.

    Remedy

    Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.

  • Electrical systemInstrument cluster/panelSep 5, 2024, Campaign 24V652000

    Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."

    Risk

    An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.

    Remedy

    Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.

  • Power trainClutch assemblyFeb 23, 2023, Campaign 23V116000

    Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.

    Risk

    Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.

    Remedy

    Dealers will replace the clutch assembly and update the software, free of charge. Owner notification letters were mailed from November 16, 2023 through July 25, 2024. Owners may contact (FCA US, LLC) customer service at 1-800-853-1403. FCA US LLC's number for this recall is 19A. This recall expands and replaces previous recall 21V-028. Vehicles previously repaired under recall 21V-028 will need to have the new remedy completed.

  • Power trainClutch assemblyJan 28, 2021, Campaign 21V028000

    Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.

    Risk

    Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.

    Remedy

    FCA US LLC will notify owners, and dealers will add software to reduce engine torque capability when clutch assembly temperatures rise to a level that may damage the inner pressure plate, free of charge." FCA has ordered a stop sale for the affected vehicles as of February 25, 2021. Owner notification letters were mailed on March 4, 2021.

  • Power trainClutch assemblyMar 3, 2020, Campaign 20V124000

    Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.

    Risk

    The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.

    Remedy

    Chrysler will notify owners, and dealers will reroute a wire harness and inspect the clutch system, and replace components as needed. The recall began April 30, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W12.

  • Show all 14 recalls
    • Seat beltsFront, anchorageSep 26, 2019, Campaign 19V680000

      Chrysler (FCA US LLC) is recalling certain 2011-2018 Jeep Wrangler right hand drive vehicles. The driver's seat belt buckle mounting strap may fracture and separate from the seat frame.

      Risk

      A separated or severed seat belt buckle strap will result in an inoperable seat belt, increasing the risk of injury in the event of a crash.

      Remedy

      FCA US will notify owners, and dealers will replace the driver's seat belt buckle, free of charge. Interim notices informing owners of the safety risk were mailed November 19, 2019. Owners will received a second letter and the recall began March 26, 2020. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is VA6.

    • EquipmentApr 23, 2019, Campaign 19V320000

      Erwin Hymer Group USA LP dba American Fastbacks (EHGUSA-AF) is recalling certain 2018 Jeep Wrangler vehicles sold with a roof top tent installed. The top cover of the roof top tent may crack or break, possibly resulting in the cover detaching from the vehicle while moving.

      Risk

      If the roof top tent cover detaches from the vehicle while moving, it can create a road hazard, increasing the risk of a crash.

      Remedy

      The remedy for this recall is still under development. The recall began May 9, 2019. Owners may contact American Fastbacks customer service at 1-844-533-7997 extension 301. Note: Vehicles in this recall are also included in recall 19V-190.

    • Latches/locks/linkagesDoors, latchNov 8, 2018, Campaign 18V786000

      Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler four-door vehicles. The right rear passenger door latch may not be in the correct location, possibly preventing the door from latching properly.

      Risk

      If the right rear passenger door opens unexpectedly, it can increase the risk of injury.

      Remedy

      Chrysler will notify owners, and dealers will repair the right rear door latch reinforcement, free of charge. The recall begin December 6, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UB6.

    • StructureFrame and membersSep 28, 2018, Campaign 18V675000

      Chrysler (FCA US LLC) is recalling certain 2018-2019 Jeep Wrangler vehicles. The front track bar brackets may be improperly welded, which can cause the bracket to separate from the frame, reducing steering capability.

      Risk

      An unexpected reduction in steering ability, can increase the risk of a crash.

      Remedy

      Chrysler will notify owners, and dealers will inspect and repair the track bar bracket welds, as necessary, free of charge. The recall is expected to begin November 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UA5.

    • Electrical systemWiring, front underhoodAug 9, 2018, Campaign 18V524000

      Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.

      Risk

      A vehicle stall can increase the risk of a crash.

      Remedy

      Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.

    • SteeringMay 25, 2018, Campaign 18V343000

      Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The intermediate steering shaft may not have been properly welded causing a split where the external spline is formed.

      Risk

      If the weld seam splits, the steering wheel may lose center positioning causing a loss of steering responsiveness and increasing the risk of a crash.

      Remedy

      Chrysler will notify owners, and dealers will inspect and, as necessary, replace the intermediate steering shaft, free of charge. The recall began June 21, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U48.

    • Electrical systemWiringMay 17, 2018, Campaign 18V332000

      Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

      Risk

      If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

      Remedy

      Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

    • Power trainAutomatic transmissionMay 1, 2018, Campaign 18V280000

      Chrysler (FCA US LLC) is recalling certain 2018 Dodge Charger, Durango and Challenger, Jeep Grand Cherokee and Wrangler, Chrysler 300, and RAM 1500 vehicles. An incorrect transmission park lock rod may have been installed in the transmission.

      Risk

      If the incorrect park lock rod is installed, the transmission may not shift into 'PARK' and keep the vehicle from moving, increasing the risk of unintended vehicle movement and the risk of a crash.

      Remedy

      Chrysler will notify owners, and dealers will install the correct park lock rod, free of charge. The recall began June 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U43.

    • StructureFrame and membersApr 12, 2018, Campaign 18V231000

      Chrysler (FCA US LLC) is recalling certain 2018 Jeep Wrangler vehicles. The rear under body ladder rail may corrode, possibly reducing the strength of the rear floor pan and causing the left rear seat mount to become loose.

      Risk

      If the floor pan strength is reduced and/or the rear seat mount becomes loose, the rear seat may detach in a crash, increasing the risk of injury.

      Remedy

      Chrysler will notify owners, and dealers will inspect and, as necessary, coat the interior and exterior of the driver's side rear underbody ladder rail with three-part rust protection. The recall began September 11, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U27.

All recalls issued for this model year. To see whether any are still unrepaired on a specific vehicle, check its VIN at NHTSA.

Recent complaints1,824 total

Most reported, across all 1,824 complaints

  • Steering61%
  • Suspension19%
  • Electrical system15%
  • Electrical systemFiled Oct 4, 2026

    The front driver gauge cluster display frequently goes black. It’s done this for a while, but recently the display stays off a lot longer, making the vehicle less safe to drive. There is a recall for other Jeeps that do this, but my 2018 Jeep Wrangler JLU isn’t covered for some reason.

    Incident Dec 31, 1969

  • Unknown or otherFiled Sep 28, 2026

    Jeep Chrysler is refusing reimbursement of recall expenses incurred due to the recall. The dealership (Cutter Honolulu) arranged alternate transport while the vehicle was being repaired, as per their documentation, but had the customer bear all expenses, contrary to the " at no cost" stipulation of an NHTSA recall order repair

    Incident Jul 7, 2026

  • Power trainFiled Sep 28, 2026

    The contact owns a 2018 Jeep Wrangler. The contact stated that the vehicle was previously repaired under NHTSA Campaign Number: 23V116000 (Power Train); however, the failure persisted after the recall repair. While driving 15 MPH, the instrument cluster failed to display the gear that the transmission was shifted to. Several unknown warning lights were illuminated, and the vehicle failed to turn off. The contact stalled the engine and waited for the vehicle to shut off. The vehicle was taken to the dealer, who determined that the instrument cluster had damaged the transmission and CAN C bus connector. The dealer replaced the instrument cluster, transmission, and CAN C bus connector, but the instrument cluster again failed to display the transmission gear. The manufacturer was made aware of the failure by phone. The failure mileage was approximately 54,000.

    Incident Aug 17, 2026

  • SteeringFiled Sep 25, 2026

    My 2018 Jeep Wrangler JL has excessive play in the steering and wanders while driving, requiring frequent steering corrections to maintain the vehicle's direction, particularly at highway speeds. I have been dealing with the steering issue for over a year. I am concerned that the excessive play and wandering could result in difficulty maintaining control of the vehicle, especially at highway speeds or during an emergency maneuver. I took the vehicle to an authorized Jeep dealership for diagnosis. The dealership confirmed that the steering gear is the problem and recommended replacement. I was quoted approximately $1,418 for the repair. FCA issued TSB 08-003-21 Rev. A, which applies to 2018–2020 Jeep Wrangler JL vehicles. The symptoms identified by FCA include steering wander, pulling/leading left or right, and excessive steering play. The repair procedure calls for replacement of the steering gear and addressing the Electric Hydraulic Power Steering software. The bulletin also states that failure to complete the required repair steps may result in undesirable handling characteristics. I contacted Jeep/FCA requesting assistance with the repair because my vehicle has the same steering condition identified in FCA's bulletin and the Jeep dealership confirmed the steering gear requires replacement. FCA declined assistance based on the age/model year of the vehicle. There were no warning lights indicating the steering gear problem. The vehicle is currently available for inspection, and the defective OEM steering gear can be retained and made available for inspection after replacement if requested. I am reporting this because I believe a steering defect that causes excessive play and wandering presents a potential motor vehicle safety concern, and I am requesting that NHTSA evaluate this issue in 2018–2020 Jeep Wrangler JL vehicles.

    Incident Sep 18, 2026

  • Electrical systemFiled Sep 24, 2026

    I had Recall issue occur on my 2018 Jeep Wrangler JLU #19A Clutch Assembly. The issue also damaged the Transmission as stated possible in the recall. Additionally the dealership reported that recall required replacement of the cluster (Instrument cluster with all gauges). This was all done. However, upon picking up the jeep and driving home, I realized that the cluster was no longer showing what gear the car is in. I called and reported to the dealer. They asked me to bring in as they though might be a software update or something, they would hook to machine. In the meantime the jeep started experiencing issues where every emergency light on cluster would go off. I would lose power steering, and I could not even turn the car off. I had to stall the car to get engine to stop. I took back to dealer (Cherry Hill Jeep) the reported the "star connector" or Can C-Bus Connector needed to be replaced. I explained that this never occurred prior to recall issue so it must be covered. they said they did not know. They replaced. I went to pick up and still the car did not show the proper gear. after further review by the dealer, they believe they received and installed the wrong cluster. This cluster now caused a problem with the Can C-Bus connector, and the car still does not show what gear it is in. All cars show what gear the car is in. this jeep currently does not. the dealer claims that the software update does not include the gear. This is not how i purchased the car or how i dropped it off prior to recall issue. Dealer is trying to charge me for labor of Can C-Bus connector and install for over $1000 and the car still does not show the gear. I have claim with Stallantis #98090202 they keep pointing to dealer. Dealer keeps pointing to Stallantis. A car must show the gear. This is safety concern to drive the car.

    Incident Jun 11, 2026

  • Power trainFiled Sep 23, 2026

    FCA US LLC is actively violating the intent of Safety Campaign 23V-116 by refusing to cover out-of-pocket consequential transmission damages. FCA’s own Part 573 Defect Report explicitly admits that the defective clutch pressure plate causes extreme friction, overheating, and fracturing capable of damaging the transmission case and nearby internal components. The vehicle operated under these defective parameters prior to the recall execution, subjecting the transmission internals to progressive thermal fatigue and severe structural vibration. This directly induced a premature internal mechanical failure less than 9,000 miles after the recall was performed. When a reimbursement claim was submitted for this consequential damage, Jeep Customer Care explicitly denied the claim under a corporate case file, stating the transmission components "are not covered under the recall repair," completely ignoring FCA's own federal defect acknowledgments. I am requesting a federal investigation into FCA’s systemic refusal to cover consequential powertrain failures caused by this safety defect.

    Incident May 19, 2025

  • Power trainFiled Sep 21, 2026

    report to the dealer that my 2018 jeep has recall for clotch overheating and vehicle can catch on fire , and it has been 3 years with no respond or completion or the job been done , feel kind of scared for the safety of me and my family every day driving ah vehicle can catch on fire . please help us to resolve this situation thanks

    Incident Jul 13, 2026

  • EngineFiled Sep 18, 2026

    Misfire no. 4cylinder due to head gasket leak and coolant leaking into cylinder.

    Incident Jan 10, 2026

  • Engine and engine coolingFiled Sep 17, 2026

    See attached document for complaint.

    Incident Jul 22, 2026

  • Power trainFiled Sep 8, 2026

    manual transmission pops out of 2nd gear during deceleration, (grinding not all the way in nuetral) untill put back in gear again. getting worse over time. found alot of same thing on internet, some getting 2 ,3, or 4 transmisions under warrenty

    Incident Jul 1, 2026

  • Show the 50 most recent
    • Service brakesFiled Sep 2, 2026

      2018 Jeep Wrangler rubber brake lines collapsing internally, trapping hydraulic fluid pressure, and causing front brakes to overheat/lock up. Happened last year on my driver's side. It completely locked up my caliper. Ended up replacing Front Driver Hose & Caliper. And both Front Rotors and Brake Pads. Now its currently happening to my passenger side. This time its actually causing a burning smell. Last year it did not it was just grinding. Been for a few months. At first I though it was my aux battery that was dead and was causing the smell. But got that looked at and didnt even have a ln aux battery. Didnt notice the smell for a few months. But now in extreme heat and worsen driving conditions it has came back. Was told my hose is collapsing. So now I have to replace rotors and brake pads again. And new hose and caliper on my passenger side

      Incident Jul 15, 2026

    • Power trainFiled Sep 1, 2026

      The contact owns a 2018 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, there was an abnormal burning odor inside the vehicle. No warning lights were illuminated. In addition, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The vehicle was taken to the dealer, and the contact was informed that parts for a recall repair might have been replaced with defective parts. The contact was informed that there was no failure and the vehicle was released; however, the failure reoccurred. The vehicle was taken back to the dealer, where it was confirmed that the clutch was slipping. The contact was informed that the clutch needed to be adjusted. The vehicle was repaired, but the failure reoccurred. The vehicle was taken to the dealer, and the contact was informed that the failure was because the contact was changing gears at 2,000 RPM and the gears should be shifted at 2,500 RPM. The vehicle was taken to an alternative dealer where the contact was informed that the recall repair was completed incorrectly. The contact was informed that the recall repair needed to be performed a second time. The vehicle was not repaired. The contact received notification of NHTSA Campaign Number: 23V116000 (Power Train). The contact stated that the vehicle was experiencing the failure prior to the recall repair, but the failure became more persistent after the recall repair was completed. The manufacturer was made aware of the failure, and a case was filed. The contact was informed that a second recall repair was denied. In addition, the contact was advised to take the vehicle to the initial dealer for a diagnostic test. The failure mileage was approximately 23,050.

      Incident May 27, 2026

    • Power trainFiled Aug 27, 2026

      Recall 19A was a full clutch assembly replacement on January 2024 at 60,000 miles. I purchased the vehicle in January 2025 with 64,000 miles. I have owned the jeep for 1 year and 8 months. I now have 78,000 miles. Service transmission light comes and goes if the vehicle cools down the light goes off and drives normal. When the service transmission light is on the clutch is overheated and slips I can not move the vehicle out of 1st gear. I drove it to a dealer and they state I have a bad clutch it is overheating. I do not believe I should pay for a clutch after a brand new clutch kit was installed 17,000 miles ago.

      Incident Aug 25, 2026

    • Electrical systemFiled Aug 27, 2026

      Suspected CAN bus failure causing multiple dash lights intermittently to include loss of power steering while driving causing an immediate safety concern.

      Incident Aug 14, 2026

    • Electrical systemFiled Aug 27, 2026

      there is open recalls for the 2018 JLU wrangler models - however mine is not included onthe recall list - but I HAVE HAD TO REPLACE THE CLUSTER FOR THE EXACT REASONS THAT ARE BEING RECALLED. I have the service paperwork and receipts - I just had this done a couple months ago. Please advise as I would LOVE a refund. I love my jeep but this was definitely a mandatory safety issue that could not wait for a recall. now there is one and my jeep needs the official recall add. Thanks

      Incident May 26, 2026

    • Visibility/wiperFiled Aug 27, 2026

      The contact owns a 2018 Jeep Wrangler JK. The contact stated that while driving at an undisclosed speed, the front windshield wipers failed to operate. An independent mechanic was contacted and reached out to the dealer to obtain a wiper power module for the repair; however, the part was unavailable. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 11,000.

      Incident Feb 28, 2026

    • SteeringFiled Aug 26, 2026

      2018 Jeep wrangler had a recall for the violently shaking front end suspension that happens while driving at high speeds of 65-70 mph and I hit a small bump. Also commonly known as the "death wobble". When this happens, I need to slow car down and pull onto the shoulder in order to get it to stop, which is very dangerous on the highway. The Repair the dealer did on this was a knowingly temporary fix. When the violent shaking returned a few thousand miles later, I was told it is not covered under the recall. They are putting a bandage on the problem instead of actually fixing. They know this wobble will return. I do not drive a lot, so it took months for this issue to come back. I had an independent service center try to fix it and was unable. I currently do not feel safe driving this Jeep on the Highway. Jeep changed the frontend suspension in 2018.

      Incident May 1, 2026

    • Electrical systemFiled Aug 26, 2026

      The contact owns a 2018 Jeep Wrangler. The contact stated that while driving approximately 20 MPH, the instrument cluster display malfunctioned, and a solid black screen was displayed. During the failure, the speedometer and warning lights were not available. The cause of the failure was not yet determined. The manufacturer was notified of the failure and informed the contact that the VIN was not included in NHTSA Campaign Number: 24V652000 (ELECTRICAL SYSTEM). The contact stated that the vehicle had experienced the failure listed in the recall. The local dealer was not contacted. The failure mileage was 100,000.

      Incident Aug 11, 2026

    • Power train, electrical systemFiled Aug 20, 2026

      The contact owns a 2018 Jeep Wrangler. The contact stated that while the vehicle was parked, the instrument panel was inoperative, except for the RPM gauge and speedometer. The contact researched and became aware of an unknown recall; however, the VIN was not included. A dealer was contacted; however, the vehicle was not yet diagnosed. The contact stated that while driving at an undisclosed speed, the vehicle suddenly lost automotive power and then stalled. No warning lights were illuminated. The vehicle was unable to be shifted into any gear and became inoperative. The San Antonio Police Department was contacted to assist with moving the vehicle out of traffic so the vehicle could be towed. The vehicle was towed to an independent mechanic, where it was diagnosed and determined that the instrument cluster had short-circuited and caused the powertrain to become unable to shift into any gear. The mechanic determined that the instrument cluster needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was unknown.

      Incident Jan 20, 2026

    • Electrical system, service brakesFiled Aug 19, 2026

      On Monday, XXX, my 2018 Jeep Wrangler JKU had several errors displayed on the dashboard: ABS, Brake, and Traction Control failures. I took my vehicle to an auto repair shop and they diagnosed it as a faulty ABS Module. This part is on back-order as per discussion with local Jeep dealers in [XXX]. Stellantis confirms that this part is not available as it has been deemed a systematic failure. There is currently no solution from Stellantis which is causing safety concerns and increased risk of operating my Jeep Wrangler. The error code is C2200: ANTI-LOCK BRAKE MODULE INTERNAL - STORED. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

      Incident Aug 10, 2026

    • Steering, electrical system, forward collision avoidanceFiled Aug 18, 2026

      Change the ending so it is completely accurate: The electric power-steering assistance and electrical/instrument-panel systems have repeatedly malfunctioned. Power-steering assistance failed while I was driving on August 3, 2026, and again on August 8, 2026. Each time, the steering suddenly became extremely difficult. I struggled to maintain control and pull over safely without being struck or causing a collision. This placed me, my passengers, and other motorists at serious risk. The Jeep also displays numerous warning lamps and messages, the instrument cluster and odometer malfunction, the radio loses sound, and reverse sometimes will not engage. Multiple electrical systems can malfunction simultaneously. Five people have witnessed these problems. Electrical symptoms existed when I purchased the Jeep in May 2024. Federico Chrysler Dodge Jeep Ram inspected it in July 2024 at 44,780 miles. The dealer documented a disappearing odometer, multiple warning lights, failure to start, required jump-starts, and inability to turn the vehicle off. Federico diagnosed an internal instrument-cluster failure and replaced the cluster. Similar problems continued intermittently afterward and became substantially worse beginning July 11, 2026. Federico recently reviewed my video. A technician considered a possible wiring problem, but the dealership requires a paid diagnostic before confirming the cause. The current failure has not been physically diagnosed. Mopar received my report and video but has not inspected the Jeep or provided a technical determination. Police, insurance representatives, and independent shops have not inspected it. The Jeep has fewer than 65,000 miles and is available for inspection upon request. I limit driving as much as possible because I believe it is unsafe, but I have no other vehicle and must occasionally drive it for essential transportation.

      Incident Jul 11, 2026

    • StructureFiled Aug 18, 2026

      The doors, hinges, hood and other places is rusted, bubbled and huge 1-2" pieces of paint are coming off the 2018 Jeep JL Rubicon Unlimited at 32-35k miles. This is absolutely unacceptable when my unrestored 1988 Jeep Comanche is rust free! Been to every dealership around and they confirm it's an issue with these, but refuse to fix.

      Incident Feb 7, 2025

    • Service brakesFiled Aug 18, 2026

      I took it in for the Maine state inspection and it won't pass because the rotors have delaminated, the caliper is starting to shift up, and the brake hoses are going bad already. The service tech says this is a known issue with these vehicles. Unacceptable for a vehicle with 42k miles.

      Incident Aug 14, 2026

    • Service brakesFiled Aug 15, 2026

      2018 Jeep Wangler JK experienced a brake failure due to a rusted collapsed right front brake line. Vehicle is one owner with 29,855 miles at time of repair on 08/05/26. Repaired by independent service center. Garage kept for the first 6 of 8 years of ownership, never operated off road, and no accidents. Parked in a covered car port for last two years when not in use. This is a well maintained, daily driver vehicle driven by a 79 year old male.

      Incident Aug 1, 2026

    • Electrical systemFiled Aug 12, 2026

      The contact owns a 2018 Jeep Wrangler. The contact stated that while the vehicle was parked with her son inside the vehicle, the instrument panel went blank. No warning light was illuminated. A dealer was contacted. The vehicle was taken to a dealer where it was diagnosed and determined that the instrument cluster needed to be replaced. The vehicle was not repaired. The failure had occurred several times. The contact associated the failure with NHTSA Campaign Number: 24V652000 (ELECTRICAL SYSTEM); however, the VIN was not included in the recall. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline to report the failure. The approximate failure mileage was 106,000.

      Incident Jul 31, 2026

    • SteeringFiled Aug 10, 2026

      The steering column mechanically disconnected, causing a complete loss of steering control while traveling approximately 70 mph on a highway. I was in the right lane when steering control was lost without any warning signs, including noises, vibrations, warning lights, or increased steering resistance. I immediately activated the hazard lights, informed my passenger, checked surrounding traffic, and applied the brakes. The vehicle pulled to the left under braking, crossed into the left lane, and entered the grassy median. The vehicle continued through a steep V-shaped median and came to a stop before entering opposing traffic. A collision was narrowly avoided.

      Incident Aug 7, 2026

    • Electrical systemFiled Aug 10, 2026

      When driving or upon start up the instrument panel cluster goes black not being able to see speedometer or gas gauge.

      Incident Jan 25, 2025

    • Service brakesFiled Aug 8, 2026

      The vehicle experienced repeated braking system failures that caused the front brakes to lock up while driving, overheat, and begin smoking. The front brake calipers, rotors, and pads were replaced multiple times,not lasting more than 3weeks before failing again. the problem continued to occur. The brake booster brake line and brake fluid were also replaced while attempting to diagnose the problem. Warning lights/messages appeared, including the ABS/traction control warning and “Service Electronic Stability Control.” The vehicle would also randomly turn off at stop lights and refuse to turn back on. An independent mechanic ultimately diagnosed a failure of the ABS control module. Showing a code “c2200” The vehicle is currently at the repair facility and is available for inspection. This failure created a serious safety risk because the brakes could engage/lock unexpectedly while the vehicle was being driven and the braking system became severely overheated and damaged multiple times. The vehicle is currently considered unsafe to drive unless I redo the whole braking system again and unplug the ABS module. I was informed that the required replacement ABS module is on national backorder with no reliable availability date and reliable refurbishes are also unable to do the repairs now. . I was also informed that obtaining a new replacement module may take an extended period of time. Because this is a safety-critical braking component, I am concerned that other vehicles with the same failure could experience unexpected brake malfunction or loss of safe braking control

      Incident Mar 25, 2026

    • Electrical systemFiled Aug 7, 2026

      I have a 2018 Jeep Wrangler JL. Both digital and analog dash gauges have stopped working. I am unable to read odometer, speedometer, gas level, RPM, temperature gauge, etc. This poses a significant risk to my safety while driving.

      Incident Aug 6, 2026

    • Service brakesFiled Aug 6, 2026

      3 out of the 4 calipers have failed.

      Incident Aug 5, 2026

    • Service brakesFiled Jul 26, 2026

      The abs module has failed and i have no traction control or abs function all the lights are on the dash a common issue with the jk jeep wrangler platform

      Incident Apr 30, 2026

    • StructureFiled Jul 15, 2026

      1 - rear door opened while driving, door was checked closed before driving on 7/14/26, it is available for inspection 2 - safety for others were at risk, as some of contents exited vehicle on road 3 - have an appointment on 7/21/26 with original cr dealer 4 - waiting on car dealer to inspect it 5 - no warning lights or messages, first apppeared on 7/14/26

      Incident Jul 14, 2026

    • Engine, fuel/propulsion systemFiled Jul 13, 2026

      I purchased this 2018 Jeep Wrangler JK Unlimited on July 19, 2025. Since purchasing the vehicle, I have experienced repeated mechanical failures that have required multiple repairs. The most serious issue involves the engine overheating at highway speeds without any visible coolant leak or clearly identifiable cause.Despite seeking professional diagnosis, the source of the overheating could not be determined. Shortly afterward, the vehicle developed a P0302 (Cylinder 2 Misfire), raising concerns about possible internal engine damage caused by the overheating.I believe this presents a significant safety hazard. An engine that overheats unexpectedly while driving at highway speeds can lose power or fail without warning, creating a dangerous situation for the driver and surrounding traffic. The vehicle has become unreliable and unsafe to operate because I cannot predict when it may overheat or experience another engine failure.As someone who often drives alone, I no longer feel safe taking this vehicle on long trips. I am concerned that the vehicle could leave me stranded on a highway or in a remote location without warning, placing my personal safety at risk. A vehicle should provide dependable transportation, not expose its occupants to the possibility of sudden mechanical failure.This vehicle has spent more time in repair facilities than on the road. I have incurred thousands of dollars in repair expenses, and I am now being asked to pay for an engine teardown simply to determine the cause of the failure before any warranty consideration can be made. Despite multiple repair attempts, the underlying cause of the overheating and engine problems has not been resolved.I am submitting this complaint because I believe the repeated overheating, unexplained engine malfunction, and resulting cylinder misfire may indicate a safety-related defect that warrants investigation. I request that the review to determine whether similar failure whether a broader safety issu

      Incident Mar 3, 2026

    • Electrical systemFiled Jul 13, 2026

      The instrument cluster display in my 2018 Jeep Wrangler Sahara has failed. The display is either blank or nonfunctional, preventing me from viewing critical vehicle information and safety warnings while driving. This failure affects my ability to monitor engine temperature, fuel tank capacity, warning messages, fault indicators, and other important vehicle operating information. As a result, I may not be alerted to potentially dangerous conditions such as engine overheating, low oil pressure, charging system failures, or other safety-related issues. I am aware that Jeep has issued recalls involving instrument cluster defects on certain Wrangler vehicles, but my VIN is not included in the recall. The symptoms of my vehicle appear similar to those reported in recalled vehicles. Because the instrument cluster is a primary safety component used to communicate vehicle warnings and operating conditions to the driver, I believe this defect presents a safety risk. I am submitting this complaint so the issue can be investigated and to determine whether additional vehicles should be covered.

      Incident Nov 22, 2025

    • Electrical systemFiled Jul 13, 2026

      The contact owns a 2018 Jeep Wrangler. The contact stated that upon starting the vehicle the instrument panel would not illuminate, due to the failure, no warning lights were illuminated. The vehicle was taken to a local dealer where the vehicle was diagnosed and the contact was advised that the instrument panel was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and offered no assistance as the vin was not allocated to a recall. The failure mileage was 50,000.

      Incident Feb 23, 2026

    • Service brakes, hydraulicFiled Jul 6, 2026

      The contact owns a 2018 Jeep Wrangler JK. The contact stated that the ABS warning light was illuminated. While driving, the vehicle experienced a loss of traction, a pulsating or pumping sensation in the brake pedal, and skidded easily upon heavy brake application. The contact associated the failure with NHTSA Campaign Number: 24V896000 (Service Brakes, Hydraulic); however, Jeep models were not included in the recall parameters. The vehicle was taken to a dealer, where it was diagnosed with electronic control unit (ECU), electronic stability control (ESC), traction control, and ABS failures. The vehicle was not repaired because the parts were on backorder. The manufacturer was notified of the failure. The failure mileage was 42,000.

      Incident Jul 6, 2026

    • Steering, service brakes, hydraulic, power trainFiled Jun 23, 2026

      The contact owns a 2018 Jeep Wrangler. The contact stated that while driving 20 miles away after an hour, the vehicle lost power steering and power braking functionality, and the transmission unexpectedly downshifted to a lower gear. The vehicle was turned off. The check engine warning light was illuminated. The vehicle was towed to the residence. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 91,300.

      Incident Jun 19, 2026

    • Unknown or otherFiled Jun 22, 2026

      EGR pre conditions to pass CA state smog emissions test will not clear. Have changed entire EGR system and have drive the recommended Chrysler Drive cycle for my car with hundreds of miles on it since replacing battery with no luck. All other system checks clear.

      Incident Jun 22, 2026

    • Electrical system, engineFireFiled Jun 22, 2026

      What component or system failed or malfunctioned, and is it available for inspection upon request? Jeep started on fire and is still at a tow yard in Belchertown, MA How was your safety or the safety of others put at risk? The Jeep started on fire while I was driving. I pulled over as the engine was smoking and then it burst into flames while I was still inside. Has the problem been reproduced or confirmed by a dealer or independent service center? Not that I know of. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives or others? Yes, we gave permission for our insurance agency and Jeep to inspect the burned out vehicle. Were there any warning lamps, messages or other symptoms of the problem prior to the failure, and when did they first appear? While I was driving, the engine temp and coolant warning lights shot way up and then the engine began to smoke. I pulled over and before I could exit the vehicle, fire was coming into the cab through the air vents.

      Incident Jun 16, 2026

    • Steering, suspensionFiled Jun 10, 2026

      Any time I am over the speed of about 55 mph, and hit any type of bump, the steering wheel starts to shake violently. I have to slow down to about 40 mph to make it stop. I almost got rearended by an 18-wheeler yesterday on the interstate.

      Incident Jun 9, 2026

    • Engine and engine cooling, power trainFiled Jun 10, 2026

      The contact owns a 2018 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the steering wheel seized and the vehicle failed to accelerate. The electronic parking brake, check engine, and several other unknown warning lights were illuminated. The contact shifted to park (P) and then drive (D) and was able to continue driving. The vehicle was taken to the dealer, who was unable to duplicate the failure. The vehicle was taken to an independent mechanic, who determined that coolant had leaked into the computer and damaged the battery pack control module. The mechanic related the failure to Customer Satisfaction Program: Y40 (Control Module Software Updates); however, the VIN was not included. The vehicle was then towed to an unknown dealer; however, the vehicle was not yet diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 100,000.

      Incident Dec 1, 2025

    • Service brakesFiled Jun 4, 2026

      I own a 2018 Jeep Wrangler that my 19 year old son drives for college. While driving, the vehicle jerked and became sluggish. There were no warning lights illuminated. I became aware that the front brake rotors had overheated again. I had the front right brake caliber and brake line changed back in 2024 and the issue has recurred this year. I had a local mechanic change the front brake pads and rotors for both front tires and caliber to right front side only in April/2026 and the issue has started again today. The vehicle was taken back to local mechanic to be diagnosed again. He stated that the brake fluid was unable to properly bleed through the brake line restricting air to fully purge from the hydraulic system, which can result in incomplete bleeding, reduced braking performance, uneven pad wear, brake drag, or brake fade and is part of the reason for burning smell near right front tire. He added that car isn’t safe to drive in this condition due to safety concerns of accidents due to inability to properly brake or even a fire. Vehicle hasn’t been repaired due to cost and I will attempt to contact manufacturer. The initial mileage reading when this issue occurred in 2024 was 90,000 miles. The mileage as of this complaint is 112,392.

      Incident Jun 4, 2026

    • Electrical systemFiled May 30, 2026

      My electronic instrument panel went completely out. I could not tell my speed, amount of gas, mileage, or anything else. This happened suddenly and without any warning.

      Incident May 29, 2026

    • Power trainFiled May 28, 2026

      I had the clutch plate recall done on my 2018 jeep wrangler unlimited 3.6 in January 2024. The first 8 months my dash lite up warning me my clutch is overheating and to reduce clutch use. This happens every time im on traffic or reversing around obstacles going up hill. The dash also lite up saying clutch performance is limited reduce clutch use. This is still happening after the recall was completed and its May 2026 currently trying to get it fixed. I have pictures of the dash lighting up with 3 different warning about the clutch plate

      Incident Aug 16, 2024

    • EngineCrashFiled May 22, 2026

      Was stopping at red light. Got to about 5mph when Jeep accelerated to about 35mph. I was standing on the breaks but the Jeep kept accelerating until impact struck the car in front me which was stopped. I have video.

      Incident May 22, 2026

    • Electrical systemFiled May 20, 2026

      Defect in the instrument panel cluster (IPC) that can cause it to go blank or fail entirely. Screen is completely blank which makes it impossible to monitor or see any warnings for vehicle with it being an electrical dash. There is a safety recall on 2018-2024 Wranglers, but for some reason my VIN does not populate on the recall when I have a 2018 Wrangler. This has caused me not to be monitor oil life, fuel, and see check engine notifications. NHTSA Recall Number: 24V‑652 for year model 2018–2024 Wranglers (and 2020–2024 Gladiators)

      Incident Mar 20, 2026

    • Steering, electrical system, engineFiled May 18, 2026

      I bought this vehicle used in 2022 from CarMax. According to Jeep (Stellantis) Co. multiple recalls were fixed by the previous owner, but the patch available for 2018 Jeep Wranglers was not done. In 2024 my iphone and Mac laptop were hacked and shortly after I began having problems with my 2018 Jeep Wrangler. My alarm system started going off while I was in my home without touching or being near the FOB. When I used my FOB to unlock the doors, they would lock back before I could open the door. I was unable to use the push button start for a few minutes up to 15 minutes and in 2025 I was unable to use the push button at all on most days. I had to research a work around to be able to start my Jeep and even after that depending on the day, it takes several seconds to minutes to start it this way. On 2 different occasions as I was driving, I had no control over my steering for approx. 10 seconds. I held on to the wheel and slowed down. The control returned and I was able to drive home. I researched and found out that 2014-2018 had reports of hacking and the hacker taking control of the vehicle in multiple ways including steering, brakes, alarm system, and hacking FOB. My radio has been turned off and the stations changed. One of my FOBs was tampered with, including switching the lock and unlock button's capability, panic button was disabled, and now the FOB does not work at all. There is a loud grinding noise behind my glove box that can be heard at different times including when Jeep is turned off. Loud noises that sound like a rock hitting the window happen randomly to my front windshield, driver and passenger windows happens multiple times while I am driving and when vehicle is turned off. I took Jeep to a trusted mechanic and was told there was no way to tell and it would be better to just sell it. After I moved, I didn't experience these problems for a while, but am experiencing them again. I am concerned for my safety and anyone who may be a passenger in my Jeep.

      Incident Feb 12, 2025

    • EngineFiled May 17, 2026

      Engine - The vehicle is available but the engine was replaced. I was able to get home however there was a potential for significant engine failure. Yes it was inspected by an independent service center. Yes it was inspected by an independent service center. A check engine light came on. Upon further inspection it was a Cylinder 6 misfire P0306. When the engine was inspected further by a mechanic it was determined that the cylinder wall was damaged and that coolant had entered the cylinder. Due to the extent of the engine damage the engine needed to be replaced.

      Incident Mar 22, 2026

    • Power trainFiled May 16, 2026

      While driving my engine light comes on and I lose power like it won’t take gear I can switch to manual and it’s fine engine light pulls a code for oil pressure sensor but I’ve done paid for that to be fixed and it still doing the same as above but the engine light will go off after cutting the jeep off and stays off for a few days then out of nowhere while driving it comes back on and the process starts all over

      Incident Dec 22, 2025

    • EngineFiled May 16, 2026

      Oil cooler failure at 7 years and 90000 miles. This is a known engineering issue due to a plastic housing that is resolved by upgrading the oil cooler housing to aluminum instead of plastic. It’s a $1000 repair. Because this is an engineering issue the consumer should not have to pay the entire cost of the repair. This is a SAFETY AND ENVIRONMENTAL HAZARD DUE TO THE LEAKAGE OF OIL CAUSED BY THIS FAILURE. It should definitely be deemed a recall and fixed at the expense of the manufacturer!

      Incident Dec 1, 2025

NHTSA crash ratings

2018 Jeep Wrangler 2 DR 4WD Later Release

Overall
Not Rated
Front crash
Not Rated
Side crash
Not Rated
Rollover
3 out of 5 stars

Decode a 2018 Jeep Wrangler VIN

Get the exact trim, engine, transmission, plant and safety equipment for one specific car.

Other years